Horizontal centrifuge using method
来源:
|
作者:hkw15f153
|
Time:2016-07-15
|
106 Views
|
Share:
Horizontal centrifuge using methods, for the use of horizontal centrifuge enterprises, the problem is very concerned about the normal operation of the method and steps, you can make use of the enterprise to take detours.
Horizontal centrifuge starting process: open the auxiliary motor to open the main motor, the main engine to speed up to the speed of cleaning 3~5 minutes, open the feed pump to feed the work
Shutdown process: close the feed pump, close the main motor, the host down speed to 2000 rpm / min, turn off the auxiliary motor, or press the cleaning button, enter the cleaning procedure.
Cleaning process: according to the cleaning button; the main motor and the auxiliary motor speed up to the cleaning speed, open the cleaning water valve, water cleaning 2 minutes; closure of the main motor, after the shutdown, repeat cleaning procedure 2-3 times; if after 2-3 times of cleaning process also failed to wash machine, viscous material often appear such situation), please the Deputy motor are arranged into the inversion (D631 set to 24), the speed of 500-1000 RPM / min, and then according to the cleaning procedures for cleaning, after cleaning please revert to the parameters.
Horizontal centrifuge alarm processing:
Fault alarm for main, auxiliary motor and feed pump
Receiving the alarm signal, alarm bells ringing, feed pump shut down, vice principal of click and deceleration stop, fault indicator intermittent flicker:
Horizontal centrifuge auxiliary motor over load:
Auxiliary motor frequency converter current CD048 set overload current limit (factory is set was 100%), feed pump shut down, within 2 minutes (the time regulation sj2) such as current does not reduce, will be transferred to the fault alarm procedures, such as the current decreases, alarm will be automatically cleared feed pump is turned on and system recovery. If the feed pump automatically stops and the recovery of the phenomenon, please reduce the feed amount.
Horizontal centrifuge block processing:
Emergence of material jam fault, the machine will alarm and shutdown, processing method: shutdown, please set auxiliary frequency converter CD631 parameters for 24, according to the cleaning button, the Deputy motor reversal, the machine discharge buildup and plugging material handling, please restore the parameter settings.
Horizontal centrifuge using methods, for the use of horizontal centrifuge enterprises, the problem is very concerned about the normal operation of the method and steps, you can make use of the enterprise to take detours.
Horizontal centrifuge starting process: open the auxiliary motor to open the main motor, the main engine to speed up to the speed of cleaning 3~5 minutes, open the feed pump to feed the work
Shutdown process: close the feed pump, close the main motor, the host down speed to 2000 rpm / min, turn off the auxiliary motor, or press the cleaning button, enter the cleaning procedure.
Cleaning process: according to the cleaning button; the main motor and the auxiliary motor speed up to the cleaning speed, open the cleaning water valve, water cleaning 2 minutes; closure of the main motor, after the shutdown, repeat cleaning procedure 2-3 times; if after 2-3 times of cleaning process also failed to wash machine, viscous material often appear such situation), please the Deputy motor are arranged into the inversion (D631 set to 24), the speed of 500-1000 RPM / min, and then according to the cleaning procedures for cleaning, after cleaning please revert to the parameters.
Horizontal centrifuge alarm processing:
Fault alarm for main, auxiliary motor and feed pump
Receiving the alarm signal, alarm bells ringing, feed pump shut down, vice principal of click and deceleration stop, fault indicator intermittent flicker:
Horizontal centrifuge auxiliary motor over load:
Auxiliary motor frequency converter current CD048 set overload current limit (factory is set was 100%), feed pump shut down, within 2 minutes (the time regulation sj2) such as current does not reduce, will be transferred to the fault alarm procedures, such as the current decreases, alarm will be automatically cleared feed pump is turned on and system recovery. If the feed pump automatically stops and the recovery of the phenomenon, please reduce the feed amount.
Horizontal centrifuge block processing:
Emergence of material jam fault, the machine will alarm and shutdown, processing method: shutdown, please set auxiliary frequency converter CD631 parameters for 24, according to the cleaning button, the Deputy motor reversal, the machine discharge buildup and plugging material handling, please restore the parameter settings.
.png)
